clutch flywheel

Product Image Product+ Price
adjusting screw, clutch arm

Adjusting screw on the clutch arm on the back of the transmission on many models over several decades. Not used on 4 speed transmissions in V700, ... more info

Part Number: 14090400

alternate clutch outer body, double o-ring, slightly longer

Here's an interesting new part out of Italy, a new version clutch outer body, or clutch push rod plunger using 2 sealing o-rings to help prevent ... more info

Part Number: 14086100B

Circlip, clutch input hub, V700, Ambassador, V750 Special

Circlip, clutch input hub, 4 speed transmission on V700, V750 Special 1969-1971, Ambassador . Also used on the primary and lay shafts on Nuovo ... more info

Part Number: 90271025

clutch bearing inner body Many Guzzi models

Clutch bearing inner body. This is the inner half of the clutch push rod throw out bearing assembly, many Big Twin and Small Block 5 models 1972 ... more info

Part Number: 14086000

clutch friction plate, V50, Monza substitute 19084450

clutch friction plate, V35, V50, V50 II, V50 III, Monza substitute 19084450. Spline diameter about 17mm Due to manufacturer and model variations, ... more info

Part Number: 27084420

clutch hub deep 4mm spline, as used since 1989 big twin 5 speeds

Commonly refered to as clutch hub, transmission input gear, clutch center, clutch gear, etc. This is the deep 4mm spline version as used by Guzzi ... more info

Part Number: 30081810

clutch input spline, hub, V700, Amb 4 speeds

Clutch input spline, clutch hub, transmission input gear, for the 4 speed transmissions as found in V700, Ambassador, V7 Special

Part Number: 12081801

clutch intermediate plate

Clutch intermediate plate for all big twin dual plate clutch models. This standard replacement intermediate plate has been an outstanding performer ... more info

Part Number: 12082300

clutch intermediate plate

Clutch intermediate plate for all big twin dual plate clutch models. This new clutch intermediate plate has a more accurate tooth profile and is ... more info

Part Number: 12082300B

Clutch lever arm spring, back of transmission

Clutch lever arm spring, back of transmission

Part Number: 94321105

clutch outer body, Many Guzzi big and small twin models

Outer clutch push rod plunger, "clutch outer body" in the parts books. Many big twins and small twins.This is the outer half of the clutch push rod ... more info

Part Number: 14086100

clutch plate kit, steel and friction plates, Convert

clutch plate kit for V1000 Convert. Includes all steel and friction plates

Part Number: 18082350

Clutch plate V7s, V7 IIs, Breva, Nevada, V65s GU32084410

Clutch friction plate, V7 Classic, V7 Stone, V7 Stone II, V7 Special, V7 Special II, V7 Cafe, V7 Racer, V7 Racer II, V7 Stornello II, Breva 750, ... more info

Part Number: 32084410

clutch pressure plate

clutch pressure plate for all big twin Guzzi clutches using 8 springs and 2 clutch plates , spanning the years 1967-2013 in 700cc, 750cc, 850cc, ... more info

Part Number: 12082901

clutch push rod seal V50 V7 Classic V7 Racer V7 Stone

Clutch push rod seal for small twins: V35, V35 II, Imola, V50, V50 II, V50 III, V50 Monza, V65C, V65SP, V65TT, V65 Lario, Nevada, Nevada Club, Nevada ... more info

Part Number: 90400616

clutch push rod seal, conical most Big Twin Guzzis

Conical clutch push rod seal. These conical clutch push rod seals have been used by Guzzi for decades, on most Big Twin 5 speed and later 6 speed ... more info

Part Number: 14085900

clutch push rod, 5 speed transmission

standard ~245mm clutch push rod, big twin 5 speed transmissions 1972-2012. Eldorado, 850GT, V7 Sport, 750S, S3, 850T, T3, T4, T5, Convert, G5, ... more info

Part Number: 14085700

clutch spring for dual plate big twins

Standard firm clutch spring for use on all Moto Guzzi big twins with 8 spring dual plate clutches as well as on early and select late models with 10 ... more info

Part Number: 13084100

clutch throwout bearing most 4, 5 and 6 speed transmissions

Clutch pushrod bearing for most all 5 and 6 speed transmissions and late 4 speed transmissions, 22mm OD. Eldorado, V7 Sport, 850T, T3, all California ... more info

Part Number: 12087001

ergal aluminum flywheel, special order only

This part is a Special Order item. Due to limited demand, we do not normally stock it. We will order the part directly from the ... more info

Part Number: 14067051

ergal aluminum flywheel, V11 Sport/LM, Griso, Stelvio, Norge

Low inertia ergal aluminum flywheel weighs in at only 2.025 pounds. Provides quick reving, instant throttle response. Original configuration 10 ... more info

Part Number: 04067000E

Flywheel 850 LeMans, LM2 LM3 LM4 LM5, 1000S 3.3kg, ~7.3 pounds

Flywheel as used on 850 LeMans, LeMans II, LeMans III, LeMans 1000, and 1000S. This is a nice middleweight flywheel for general purpose sport and ... more info

Part Number: 14067050

flywheel bolt, hardened 10.9

flywheel bolt for standard Guzzi twin plate clutch flywheels, these should be considered one time use fasteners and should be replaced when removed

Part Number: 12067701

Flywheel T3, Cal2, SP1000, 1000S, ~4.3 kg ~9.5 pounds

Standard and touring flywheel as used on many big twin models - T3, G5, CX100, T4, T5, Strada, California II, California III, Mille GT, 1000S, ... more info

Part Number: 17067050

Hydraulic clutch slave cylinder assembly for 5 speed big twins

Hydraulic clutch slave cylinder assembly for most Guzzi big twins with 5 speed transmissions. Replace the clutch cable with a hydraulic system of ... more info

Part Number: MG5050

Lightened flywheel, 850 LeMans and similar, approx 5.5 pounds

Aftermarket pre-lightened steel flywheel suitable for all big twins with 8 spring dual plate clutches. These flywheels are lightened at the factory, ... more info

Part Number: 140670501

longer clutch push rod, 5spd, RAM clutch

For RAM clutches made after January 2015, this longer ~250mm clutch push rod may be required when used in 5 speed transmissions.

Part Number: 14085700L

MIBA sintered clutch plate for RAM low inertia clutch

New generation sintered clutch plate for RAM low inertia clutch. Stainless steel and advanced MIBA sintered friction material for superior friction ... more info

Part Number: 01084441

Newfren clutch friction plate for early shallow spline

Newfren clutch friction plate for early style shallow (~2mm deep) spline input hubs. These plates with flexible backing plates offer a smooth ... more info

Part Number: 28084460NF

Pressure plate cup, most Big Twin Guzzi models 1967 thru 2004

Pressure plate cup, big twin 700, 750, 850, 1000 and 1100cc, 4 and 5 speed transmission models with twin plate clutches. From 1967 thru roughly 2004, ... more info

Part Number: 12082800

RAM flywheel bolt plate

Flywheel bolt plate for RAM low inertia clutches. This item is not normally kept in stock, but is available by special order. Allow approximately 3 ... more info

Part Number: MG1096620P

RAM low inertia clutch kit, bikes with no flywheel sensors

RAM low inertia clutch kit for big twins with 5 speed transmissions and no flywheel sensors. RAM clutches have now had the benefit of over 16 years ... more info

Part Number: MG1096620

Replacement seal and oring kit for hydraulic clutch slave cylind

Replacement seal and oring kit for hydraulic clutch slave cylinder assembly (MG5050). Includes 2 piston orings and 2 shaft seals.

Part Number: MG5051

ring gear to flywheel bolt, 20mm long, 1972-2002

This bolt is used to attach the starter ring gear to the the flywheel on many models beginning in 1972 with the V7 Sport and extending through 2002 ... more info

Part Number: 98054420

ring gear to flywheel bolt, V700, Ambassador, Eldorado

This 25mm long bolt is used to connect the starter ring gear to the flywheel on 1967-1974 Eldorado and Ambassador and V700 models. These models have ... more info

Part Number: 98054425

SD-TEC clutch kit, 2 plates, hub, interrmediate plate 5 speeds

SD-TEC clutch kit, for 5 speed big twin Guzzis. Includes 2 clutch friction plates for 4mm deep spline clutch hubs, a matching clutch hub, an ... more info

Part Number: 30084410KIT

SD-TEC clutch plate, deep spline, bonded and riveted

SD-TEC clutch friction plate for 4mm deep spline clutch hubs is both bonded and riveted for maximum strength, smooth engagement, and durability. We ... more info

Part Number: 30084410SD

soft clutch spring for late model 10 spring clutches

These are soft clutch springs as used in 10 spring clutches as found on models such as V11 Sport (and variants), V11 LeMans (and variants), Breva ... more info

Part Number: 04084100

starter ring gear, flywheel ring gear, many models 1967 - 2012

Starter ring gear, flywheel ring gear, ~4.6 pounds, suitable for all big twins using M8 bolts to attach to flywheel . Suitable for V700, Ambassador, ... more info

Part Number: 17067900

Supplemental Installation Kit for SD-TEC clutch kit

Convenient Supplemental Installation Kit to accompany the SD-TEC clutch kit. We consider this kit to be the minimum additional items that you will ... more info

Part Number: 30084410SUP

Sureflex clutch friction plate bonded deep 4mm

Genuine Italian Sureflex brand clutch friction plate for deep spline (~4mm) clutch hubs. Bonded friction material on a solid steel backing plate ... more info

Part Number: 30084411

Sureflex clutch friction plate for early shallow 2mm spline hub

Sureflex clutch friction plate for early style shallow (~2mm) spline input hubs. These plates with bonded friction material on solid backing plates ... more info

Part Number: 28084460S

Throwout bearing early 4 speeds, 20mm

Throwout bearing early 4 speeds, 20mm diameter. Replacement for caged ball throwout bearing found in V700s and early Ambassadors

Part Number: 12087000