All Products
7/33 ring and pinion gear set 1975 to 1993 replaces GU17354650
Part number:
Final drive gear set with a 7/33 tooth count giving a 4.71 gear ratio. This gear set provides a 4.71 ratio which is common to many Guzzi big twins more info
$447.63
Rear drive box shim, large, 0.8 mm Disc brake GU17355400
Part number:
Rear drive box shim, ring gear shim, 0.8mm, most rear disc brake models T3, T4, T5, S3, Convert, G5, 850 LeMans, LeMans II, CX100, LeMans III, LeMans more info
$5.75
Rear drive box shim, large, 1.0 mm Disc brake
Part number:
Rear drive box shim, large, 1.0 mm Disc brake T3, T4, T5, S3, Convert, G5, 850 LeMans, LeMans II, CX100, LeMans III, LeMans 1000 all years LeMans IV more info
$5.75
Rear drive box shim, large, Disc brake 1.1 mm GU17355406
Part number:
Rear drive box shim, large, Disc brake 1.1 mm T3, T4, T5, S3, Convert, G5, 850 LeMans, LeMans II, CX100, LeMans III, LeMans 1000 all years LeMans IV more info
$15.52
Rear drive box shim, large, Disc brake 1.2 mm GU17355408
Part number:
Rear drive box shim, large, Disc brake 1.2 mm T3, T4, T5, S3, Convert, G5, 850 LeMans, LeMans II, CX100, LeMans III, LeMans 1000 all years LeMans IV more info
$5.07
Rear drive box shim, large, Disc brake 1.3 mm GU17355410
Part number:
Rear drive box shim, large, Disc brake 1.3 mm T3, T4, T5, S3, Convert, G5, 850 LeMans, LeMans II, CX100, LeMans III, LeMans 1000 all years LeMans IV more info
$5.32
Rear drive box shim, large, Disc brake 1.4
Part number:
Rear drive box shim, large, Disc brake 1.4
$6.12
Rear drive box shim, final drive disc rear brake 1.8 mm
Part number:
GU17355419 Rear drive box shim, large, disc brake ~1.8 mm thick T3, T4, T5, S3, Convert, G5, 850 LeMans, LeMans II, CX100, LeMans III, LeMans 1000 more info
$4.98
Final drive seal kit for rear disk brake twin shock big twins
Part number:
Best quality gasket, seals, crush washers, and orings kit to seal up a final drive box on any twin shock big twin disk rear brake model or Quota. more info
$57.05
Magnum BYO stainless brake hose, 6 foot section
Part number:
Magnum Build Your Own DOT approved braided stainless brake hose only, 6 foot section.Use only with Magnum brand fittings, which are not included. No more info
$24.26
Magnum BYO stainless brake hose, 12 foot section
Part number:
Magnum Build Your Own DOT approved braided stainless brake hose only, 12 foot section. Use only with Magnum brand fittings, which are not more info
$47.66
Magnum BYO brake banjo fitting 180 degrees (straight) 10mm
Part number:
Magnum BYO brake banjo fitting 180 degree angle (straight). No more guessing pre-cut hose lengths, simply assemble these brake hoses and fittings on more info
$18.86
Magnum BYO brake banjo fitting 35 degrees 10mm
Part number:
Magnum BYO brake banjo fitting 35 degrees angle. No more guessing pre-cut hose lengths, simply assemble these brake hoses and fittings on the bike more info
$18.86
Magnum BYO brake banjo fitting 60 degrees 10mm
Part number:
Magnum BYO brake banjo fitting 60 degree angle. No more guessing pre-cut hose lengths, simply assemble these brake hoses and fittings on the bike for more info
$17.96
Magnum BYO brake banjo fitting 90 degrees 10mm
Part number:
Magnum BYO brake banjo fitting 90 degree angle. No more guessing pre-cut hose lengths, simply assemble these brake hoses and fittings on the bike for more info
$18.86
12mm Magnum BYO brake banjo fitting 35 degrees
Part number:
12mm Magnum BYO brake banjo fitting 35 degrees angle. This 12mm is a unique size used on the rear brake hose on many V11 California models with more info
$19.76
12mm Magnum BYO brake banjo fitting 90 degrees
Part number:
12mm Magnum BYO brake banjo fitting 90 degrees angle. This is a unique size used on the rear brake hose to the proportioning valve 03657500 on many more info
$20.66
Magnum BYO brake banjo fitting 15 degrees offset 10mm
Part number:
Magnum BYO brake banjo fitting 15 degrees offset. No more guessing pre-cut hose lengths, simply assemble these brake hoses and fittings on the bike more info
$18.86
Black Magnum BYO brake banjo fitting 180 degrees (straight) 10mm
Part number:
Black Magnum BYO brake banjo fitting 180 degree angle (straight). No more guessing pre-cut hose lengths, simply assemble these brake hoses and more info
$20.66
Black Magnum BYO brake banjo fitting 35 degrees 10mm
Part number:
Black Magnum BYO brake banjo fitting 35 degrees angle. No more guessing pre-cut hose lengths, simply assemble these brake hoses and fittings on the more info
$21.56
Black Magnum BYO brake banjo fitting 60 degrees 10mm
Part number:
Black Magnum BYO brake banjo fitting 60 degree angle. No more guessing pre-cut hose lengths, simply assemble these brake hoses and fittings on the more info
$20.66
Black Magnum BYO brake banjo fitting 90 degrees 10mm
Part number:
Black Magnum BYO brake banjo fitting 90 degree angle. No more guessing pre-cut hose lengths, simply assemble these brake hoses and fittings on the more info
$19.76
Black Magnum BYO stainless brake hose, 6 foot section
Part number:
Black Magnum Build Your Own DOT approved braided stainless brake hose, 6 foot section only. No more guessing pre-cut hose lengths, simply assemble more info
$26.06
Black Magnum BYO stainless brake hose, 12 foot section
Part number:
Black Magnum Build Your Own DOT approved braided stainless brake hose only, 12 foot section. No more guessing pre-cut hose lengths, simply assemble more info
$53.06
Magnum BYO brake chrome 3 way manifold
Part number:
Magnum BYO chrome 3 way manifold. Join 3 hoses together or split 1 hose 2 ways with this single fitting. Assembles in 5 minutes or less with only more info
$44.06
Stainless side cover mount set, Convert, 850 T3, 850 LeMans
Part number:
Stainless steel side cover and rectifier mount set, Convert, 850T3, 850 LeMans. Left and right side. Part numbers14424850 and 14424050
$46.11
Side stand 1000SP T3 LM1/2/3 V7 Sport CX100 GU17432060
Part number:
GU11432001 GU14432050 Latest version of the complete side stand as used on many models of the 1970s and early 1980s. Kick stand comes complete more info
$97.18
Spring plate, side stand T3, 1000SP, LeMans II, LMIII, T5, SPII
Part number:
Spring plate for side stand: Late T3, 1000SP, CX100, LeMans II, LMIII, T5, SPII
$11.15
Spring, side stand, LMII SP CX Mille SPIII 1000S LeMans1000
Part number:
GU17434060 Side stand spring, used on original units with dual springs on various models of the late '70s and '80s. SP1000, SP II, SP III, more info
$3.54
Rear fender, mudguard, 850T3 T4 Convert Special Order
Part number:
Polished stainless steel rear fender, 850T3, T4, Convert NOTE: This item is not normally kept on hand and is available by special order. Please see more info
$425.47
Crash bar set, 850T T3 V7 Sport 750S S3 GU17450200
Part number:
Pair of crash bars (engine guards), left and right side for 850T, 850T3, 750S3 and included in the original parts books as an accessory for V7 Sport more info
$128.35
Threaded plate upper mount for crash bar and fairing mounting
Part number:
Threaded plate, upper mount for crash bar and fairing lower mounts, most Tonti frame big twin models 1972 through 2007. This threaded plate takes the more info
$9.89
seat 850-T, 850-T3
Part number:
Standard two person bench seat as used on 850T and 850T3. This is a very nice quality reproduction seat with new foam, a steel pan, a seat prop, and more info
$538.56
T3 California seat complete with chrome rail
Part number:
Excellent quality Italian made T3 California seat with chrome rail. Steel seat pan, textured vinyl true to the original pattern, chromed steel wrap more info
$617.17
stud, seat strap retaining, 850 LeMans, LeMans II, III, CX100
Part number:
Offset stud for attaching seat strap on 850 LeMans 2nd series, 850 LeMans II, CX100, 850 LeMans III, and 850T3 California. Note this item is more info
$24.96
Sidecover decal pair for 850T3 California
Part number:
Side cover decal pair for 850T3 California. White vinyl letters and a stripe fit beneath the aluminum emblems as original. These are peel and stick, more info
$22.25
Rubber for headlight ears 850T T3 Convert G5 Cal2 LeMans CX
Part number:
Rubber ring for headlight support ears,850T, T3, T4, Convert, G5, SP1000, 850 LeMans, LeMans II, CX100,LeMans III, California II, V65C, V65SP, Lario, more info
$3.99
Steering stem Eagle emblem T T3 T4 Convert G5 SP LM2 CX V50 V65
Part number:
GU17517700 Aluminum eagle emblem, approximately 29.3mm in diameter, commonly used to cap the steering stem on many models including: 850T, 850T3, T4, more info
$10.11
Adjustable steering damper SP CX LeMans 1000S EV Cal1100 Jackal
Part number:
GU03530270 GU17530260 Original equipment adjustable steering damper used on many Guzzis including: SP1000, CX100, 850T5, LeMans II, LeMans III, more info
$86.36
Lower fairing to valve cover mount SP CX LM2 LM3
Part number:
Fairing mount for chin fairings and lower fairings where they attach to the valve cover as used on SP1000, CX100, LeMans II, and LeMans III.
$28.15
T3 Police fairing cowling, bare
Part number:
This part is a Special Order item . Due to limited demand, we do not normally stock it. We will order the part directly from the more info
$210.66
Windscreen SP1000 SP II 850T4
Part number:
GU17577260 Nice Italian windshield for SP1000, SPII and 850T4 fairing, as original, smoke tint, rubber edging, heavy duty as original. more info
$159.77
Handlebar 850T, 850T3 Convert and G5 civilian, T4 no wire holes
Part number:
Original bend handlebar for 850T, 850T3 civilian, V1000 I Convert civilian, G5 civilian, and 850T4. This is the more common lower or "civilian" more info
$49.83
Handlebar SP1000 V50 V50 II SPIII T5
Part number:
This handlebar for SPIII and the T5 series, is also the substitute for the SP1000, V35s, V50 and V50 II. Dimensions in inches are approximately 27" more info
$37.52
Tommaselli Daytona 2C throttle, black 850 LeMans, GU14603450
Part number:
14603450 original part number in black. Legendary Tommaselli Daytona 2C "quarter turn" throttle assembly in black. As original on 1976 to 1978 more info
$66.13
Tommaselli Daytona 2C throttle, chrome T T3 Convert GU17603400
Part number:
17603400 original part number in chrome. Legendary Tommaselli Daytona 2C "quarter turn" throttle assembly. Chrome plated as was original on several more info
$96.46
Rubber cable boot for Tommaselli Daytona 2C throttle
Part number:
Rubber cable boot for Tommaselli Daytona 2C throttle. This is the rubber bellows like boot that fits the throttle where the cable housings fit up more info
$6.34
Polished clutch lever assembly T3 G5 Convert Cal2 SP GU17605570
Part number:
New production clutch lever assembly with polished lever as used on 850T3, T3 California, T4, California II, Convert, 1000SP and G5 1975-1984. These more info
$62.45
Polished lever for round Brembo master cyilnders GU17605652
Part number:
079554344 Polished aluminum brake lever for round reservoir PS12 to PS17 Brembo master cylinders as found on Moto Guzzi, Ducati, Benelli, more info
$25.83
Spoke, rear wheel Convert T3 G5 short side, stainless steel
Part number:
Stainless steel spoke with nipple for rear wheel as used on V1000 I Convert, 850T3, V1000 G5 750S3, and similar with Borrani rims and rear disk more info
$3.56
Bearing grease cup T3 G5 Convert Mille Jackal Vintage GU17633550
Part number:
Bearing cup, grease cup, 850T3 through California Vintage, inside rear spoked wheel on drive side, holds the grease near the wheel bearing on the more info
$4.86
Axle spacer, between bearing and caliper carrier, T3 G5 Convert
Part number:
Machined axle spacer for rear spoke wheels on 850T3, T4, V1000 G5 and Convert. Reproduction of discontinued original part. Fits between wheel more info
$22.13
Brembo anodized piston pair F08 caliper 1974 on Guzzi Ducati
Part number:
079739752 GU17654080 Pair of Brembo 38mm OD anodized aluminum pistons for F08 (P2 F08) brake caliper. Replace the rusted and pitted more info
$24.82
Brembo caliper cover for single nipple F08 calipers GU17654760
Part number:
Brembo caliper cover for single nipple F08 calipers found on later model Big Twin Guzzis, as well as current Brembo production calipers. more info
$6.76
Brake hose M/C to union V7Sport, M/C to R caliper V50s
Part number:
Rubber brake hose, multiple applications, master cylinder to rear caliper on V50, V50 II, V50 III, V50 Monza, V65SP. Updated number replacing more info
$46.48
Rubber brake hose, F MC to RF Caliper SP-LM III, banjo-male 28"
Part number:
Rubber brake hose, front master cylinder to right front brake caliper on 1000SP, LeMans II, CX100 and LeMans III, banjo fitting at master cylinder more info
$58.77
Brake hose, rear G5 T3 SP LeMans 1/2/3 R front T3 G5
Part number:
Rubber brake hose from the rear junction block to the metal brake pipe for the rear caliper on many models, including California II, G5, more info
$52.16
Brake pipe right front T3 Convert G5
Part number:
GU17658050 Rigid brake tubing connects rubber hose to right front caliper on 850T3, Convert, G5.
$29.12
Brake hose master cyl to splitters banjo-banjo GU17658550
Part number:
Rubber brake hose, banjo fitting on each end, approximately 16" long. Used from the rear master cylinder to junction block on many models, more info
$39.11
Brake pipe, rear LeMans 1/2/3 CX T3 SP G5 GU17658650
Part number:
Rigid brake tubing connects rubber hose to rear caliper on 850 LeMans, LeMans II, CX100, LeMans III, 850T3, T4, T5, Convert, G5, CX100, Mille GT, more info
$40.61
Brake pipe, long on frame T3 LeMans 1/2/3 SP Cal2 CX Convert
Part number:
Long rigid brake tubing along the upper frame rail on many models with integrated braking system from 1976 through 1986. 850 T3, T4, Convert, G5, 850 more info
$29.07
Brake hose, rubber, integrated left front T3 G5 Convert
Part number:
Rubber brake hose from the long rigid tube to the left front brake caliper when mounted in front of the fork as on 850T3, T4, Convert and G5. Female more info
$63.37
Brake hose to left caliper LeMans 2/3 SP CX Cal 2/3 V65s
Part number:
Rubber brake hose from rigid brake pipe to left brake caliper when located in back of fork leg, 1000SP, LeMans III, LeMans II, CX100, California III, more info
$46.55
Brake pipe, left front, T3 T4 Convert G5
Part number:
GU17658950 Rigid brake tubing connects rubber hose to left front caliper on 850T3, T4, Convert, G5
$29.12
Brembo 10mm bleeder nipple F08 and other calipers
Part number:
Brembo 10mm bleeder nipple, includes rubber cap. For post 1985 F08 calipers as used on Guzzis until 1996 and most single bleeder Brembo brake more info
$12.30
15mm Brembo master cylinder kit round front most rear to 2010
Part number:
GU17659350 , 066139790 , 34 31 1 237 233 Genuine OEM 15mm Brembo PS15 master cylinder repair kit. Fits rear master cylinders on all more info
$22.82
12mm Brembo master cylinder rebuild kit 1975-1984 GU17659352
Part number:
082039797 12mm Brembo PS12 master cylinder repair kit. Fits round reservior hand brake master cylinders from 1975 to approximately more info
$22.82
Round reservoir 12mm master cylinder T3 G5 SP LeMans GU17660253
Part number:
082054335 Old style round reservoir ~12mm hand master cylinder. This master cylinder will operate a single F08 (or F05) brake caliper and is a more info
$152.99
Brembo cap and bellows 12mm round reservoirs GU17661052
Part number:
GU17661152 , 800027065 , 082039676 Genuine Brembo 110430830 plastic PS11/PS12 master cylinder cap and rubber bellows, for 12mm round more info
$11.39
70mm spring for rear brake master cylinders
Part number:
70mm spring common to rear master cylinder lever on many models, also used as air filter box spring. T3 Convert G5 CX100 V50 etc. This is the more info
$4.06
50mm spring, rear brake master cylinder spring
Part number:
50mm spring commonly used as a rear brake master cylinder return spring. This spring is used on a variety of models, often used on 1976 to 1994 Tonti more info
$4.81
Alternator brush holder for Bosch alternators GU17712452
Part number:
Alternator brush holder for Bosch alternators, complete unit with brushes and springs. Original to V7 Sport, 750S, S3, 850T, T3, T4, T5, Convert, G5, more info
$44.34
Alternator rotor, ~3.4 ohms for Bosch charging systems Guzzi BMW
Part number:
GU17712457 12311244642 V7 Sport, 750S, S3, 850T, T3, T4, T5, Convert, G5, 850 LeMans, LeMans II, CX100, LeMans III, LeMans 1000 all more info
$116.16
ZADI ignition switch, most Guzzis 1975 to 1997 GU31735360
Part number:
GU17735350 850T3, S3, T4, most T5, Convert, G5, 850 LeMans, LeMans II, CX100, LeMans III, LeMans 1000 all years LeMans IV and LeMans V, 1000S, Mille, more info
$25.69
Metal ignition switch ring nut, many models
Part number:
This is a replacement ring nut for ignition switches on many models. Fits original and aftermarket Zadi switches with standard 21mm x 1.00 thread more info
$16.14
Ignition switch housing, Convert, 850 T3 LM I LM II
Part number:
Ignition switch holder as used on V1000 Convert, 850T3, T4, 850 LeMans, LeMans II. This switch fits the top frame rail in the front notch in the fuel more info
$39.01
Economy CEV replica tail light, black base alternate to 17740900
Part number:
GU17740900 079574153 Economy replica CEV 9350 tail light assembly, with black plastic base. Alternate for the chrome version found on more info
$28.24
Fuse, 16 amp, euro-style most Guzzis thru mid 80's GU17742550
Part number:
16 amp fuse as used on most models 1967 through mid 80s, plus a couple oddballs from the early 90's.. Suitable for V700, Ambassador, 1969-1971 more info
$0.64
25 amp fuse euro-style most Guzzis thru mid 80's GU12742500
Part number:
25 amp fuse as used on most models 1967 through mid 80s, plus a couple oddballs from the early 90's.. Suitable for V700, Ambassador, 1969-1971 V750 more info
$0.64
Fuse box with cover Guzzi big blocks '75 to '85 GU17743000
Part number:
Fuse box for many 1970s and 1980s models including: 850T, 850T3, 850T4, 850T5, V1000 I Convert, V1000 G5, 850 LeMans, 850 LeMans II, CX100, 850 more info
$30.23
Fuse box cover, clear guzzi big blocks '75 to '85 GU17743100
Part number:
Clear fuse box cover with thumb screw for many 1970s and 1980s models including: 850T, 850T3, 850T4, 850T5, V1000 I Convert, V1000 G5, 850 LeMans, more info
$9.27
Main wire harness 850T3 Convert G5 GU17747150
Part number:
Main wire harness for 850T3, suitable replacement for Convert and G5. This harness does not include any subharness, for example, it does not include more info
$97.95
Alternator wire harness, 850T3 T4 Convert G5 GU17747450
Part number:
New reproduction wire harness for 200w Bosch alternator equipped models 850T3, V1000 I Convert, V1000 G5, and 850T4. This wiring harness includes the more info
$72.63
Flasher rubber holder T T3 Convert G5 LeMans 1/2/3 SP GU17751200
Part number:
Rubber turn signal flasher holder, many models. 850T, T3, T4, T5, Convert, G5, 850 LeMans, LeMans II, CX100, LeMans III, California II, more info
$7.82
Replica CEV turn signal, chrome T3 T4 Convert G5 Cali II V50
Part number:
Chrome plated replica of the CEV turn signal assembly as used by Guzzi during the middle seventies and early eighties. Funtional for many models and more info
$33.39
Turn signal stem for CEV, chrome, 75mm center 125mm overall
Part number:
Chrome turn signal stem for CEV turn signals with 2 nuts and 2 washers. 125mm overall length, 75mm unthreaded center section. M10 x 1.5 thread pitch more info
$22.38
Tachometer, 80mm, LeMans SP CX Mille
Part number:
Very nice replica Veglia blue face tachometer, 80mm, lighted with cable drive. Suitable for 850 LeMans, Lemans II, CX100, some Mille GT, 1000SP, SP more info
$104.20
90 degree angle cable gear set, speedo and tach GU17768360
Part number:
90 degree angle cable drive gears, used on speedometer and tachometer on many Guzzi models 1979-2002. These angled cable drive gear sets are used more info
$39.63
Oil pressure switch most Guzzis thru 2005 GU17768750
Part number:
This is the common oil pressure switch used on most all small block and big block Guzzi twins up to 2005, with the exception of the V65s and 750 more info
$11.67
Instrument console warning light holder V7 Sport 850T 750S
Part number:
This is a plastic replica of the idiot light console used on V7 Sport, 750S and 850T models. This is a replica of the 1st version, with more info
$25.11
fairing mount mirror, LM5, California III, Daytona
Part number:
Fairing mounted mirror as used on LeMans 1000 1988-1993, Daytona 1000, and California III full fairing version. Suitable for use on any flat fairing more info
$58.64
Badge, emblem, "850-T" side cover
Part number:
Aluminum emblem for side cover on 850T. Sold each, price is per emblem. Use badge clip part number 39922200 for mounting
$19.16
Badge, emblem, "850-T3" for side cover
Part number:
Aluminum side cover or battery cover emblem "850-T3". Use badge clip part number 39922200 for mounting.
$16.12
Emblem, badge, 1000SP side cover GU17922061
Part number:
Aluminum side cover or battery cover emblem or badge 1000SP, also used on SP II with the addition of the "II" emblem. Use badge clip part number more info
$17.51
side cover grill set, Convert 850T3 1000SP V1000 G5 T4
Part number:
Side cover grill set as used on Convert, 850T3, T4, 1000SP, V1000 G5, sold as a pair. Use badge clip part number 39922200 for mounting. more info
$27.11
Chrome side cover grill set: Convert 850T3 1000SP V1000 G5
Part number:
One pair of chrome plated side cover grills for Convert, 850-T3, 1000SP, and V1000 G5. These plastic grills are a direct replacement for the more info
$33.49
Dellorto choke valve assembly for PHF, VHB
Part number:
Dellorto choke valve assembly for cable operated enrichener circuits used on most VHB and all PHF carbs. Includes choke valve or plunger, choke valve more info
$14.72
Spring, Dellorto, accelerator pump spring, VHB GU17939300
Part number:
Accelerator pump spring for Dellorto VHB 29 and VHB 30 carburetors from 1968-1979. Ambassador, 1969-1971 V750 Special, Eldorado, 850GT, V7 Sport, more info
$4.00
Alternator cover spacer most Big Twins 1972 to 2005, V50 V50 II
Part number:
GU18001150 Plastic alternator cover spacer, many models, permits cooling air to reach alternator. Suitable for use on V7 Sport, 750S, S3, 850T, more info
$9.16
cast aluminum ventilation spacer for alternator cover
Part number:
Cast aluminum spacer for the alternator cover on the models listed below. This aluminum piece replaces the original plastic item permits more info
$72.85
